HYPER 212 EVO REVIEW REDDIT INSTALL
HYPER 212 EVO REVIEW REDDIT FULL
HYPER 212 EVO REVIEW REDDIT PRO

It took less than 30 secs sustained load for it to throttle at stock settings. while waiting for my NH-D15 to arrive I was running the Hyper 212 EVO from my old computer on my new 9900k.

HYPER 212 EVO REVIEW REDDIT FULL

You'll never get full performance out of a 9900k with your Hyper 212 EVO. You need to dissipate around 200W of heat if you're running at 4.6 Ghz and your cooler has a TDP of 150W. You'll be throttling in any stress test with a Hyper 212 EVO on a 9900k. Nice and quiet and good enough for me! The black looks nice had the RGB fan hooked to my ASUS mobo rolls slowly through the colors.A Noctua NH-D15 on a 9900k maxes out in the 70's degrees with no OC. With a i9-9900K and a 4.6GHz OC, I can run the fan at low speeds and have the temp max out at around 70C. It works fine as long as I don't go crazy overclocking the CPU. Johnpombrio said:I have the Hyper 212 EVO black edition which has a very similar mounting system.

HYPER 212 EVO REVIEW REDDIT INSTALL

With the new Hyper 212 Evo v2 now available, those with fond memories of their previous Hyper 212’s now have the chance to install a piece of updated nostalgia into a modern, silent HTPC system or home server, or perhaps as a piece recommended by a mentor for a novice system builder’s first PC. We’d advise double checking the appropriate motherboard CPU_FAN header (or other chosen header) to make sure the cooler has the ability to cool effectively at appropriately reported CPU temperatures. There is also a slightly lower thermal signature in the adjacent regions at full speed, which indicates the added benefit of improved airflow.Ĭonsidering the low noise levels of the Hyper 212 Evo v2 even at full speed, having a quality fan curve which favors higher fan RPM is beneficial for any system installation. The Cylon 4F looks pretty similar to the Hyper 212 Evo, and Ive got a 212 Evo cooling my 10700K with unlocked power limit and a 5GHz all-core overclock.

HYPER 212 EVO REVIEW REDDIT PRO

Our Flir One Pro thermal imaging camera shows some noticeable differences in heat soak throughout the cooling tower itself between 50% and 100%, which is to be expected. The Aerocool Cylon 4F should handle a 11400F. Omitting AVX instruction sets allows for accurate, 100% loads at chosen clock speeds, while allowing AVX instructions would provide higher, albeit, unrealistic synthetic CPU loads and excessive heat production, less indicative of real-world use. Prime95 v29.4b8 (no AVX) is used for two-hour intervals, one managing fans at 50% PWM and the other at 100% PWM with RPM measurements being taken every three seconds and averaged across the duration of each two-hour capture. 7C70v12)Ĭorsair Dominator Platinum RGB, 16GB (2x8GB) DDR4-3600ĬrystalFontz CFA-633-TMI-KU, 4x Dallas One Wire WR-DOW-Y17 sensorsĬorsair Commander Pro, 100%/50% PWM Speed profiles (liquid cooling pump always if applicable)ĭata comparisons are based on data collected from testing performed on our new Intel i9-10850K system, including re-visiting many previously covered products which were originally covered on the prior testing platform which pivoted around an i7-5930k (4.20ghz Cooler Master Hyper 212 EVO V2 at Amazon for $39.99 If you routinely have it maxed out (rendering and such) might help your peace of mind to upgrade, but I don't see it being entirely necessary for your situation.Intel Core i9-10850K LGA1200 (Comet Lake), all 10 cores 4.6Ghz 1.190v, (3.60Ghz stock speed, single core boost 5.2Ghz)

If you're not planning on overclocking, I think that temp is great for a stress test run and you only do a bit of gaming and other software. Now that being said the most common reason this cooler doesn't remain usable is that the pumps aren't the greatest out there and they do fail. The H100i is a closed loop system, meaning it should never just magically run out of coolant inside unless there is a small leak somewhere. Chances of a random leak springing up are fairly low to be honest, that being said don't work the tubing too much, it should be fairly obvious what the max you can turn it is. With 2 people fair easy, solo it can get a bit annoying depending on the person and the size of the case.ģ. Mounting the radiator with fans can get a bit annoying if you're mounting the fans between the rad because you have to balance holding the rad up with the fans while you try to get the screws aligned properly. It's both easier and harder to install the H100i than the Evo, the mounting system for the Hyper212 line is something I've never a been a fan of, a lot of better options out there and the mounting for the pump onto the CPU socket is pretty straightforward. Don't need much cable management though it never hurts to clean it up inside for the best air path possible for your fans.Ģ.

Hyper 212 evo review reddit